Furnace Craft Co logo Furnace Craft Co

Furnace Repair

Furnace Won't Turn On in Chicago, IL

A furnace that does nothing at all when the thermostat calls for heat: power, switches, transformer and control checks.

  • ✓Owner-operated
  • ✓Shop on W Irving Park Rd
  • ✓Gas and electric furnaces

Quick answer: if the furnace will not start at all, with no click, no fan and no light, the problem is usually power or a safety switch: a tripped breaker, an off switch, a loose door switch, a dead transformer or a thermostat issue. Work through the checks below, then call (773) 514 3683.

Checks you can do safely

  1. Thermostat on heat, setpoint above room temperature, fresh batteries if it uses them. 2. The furnace switch (it looks like a light switch near the unit) is on. 3. The breaker or fuse has not tripped; reset once. 4. The blower door or front panel is seated, because it presses the door switch that allows startup. 5. On a high-efficiency furnace, a condensate or float switch can stop startup if the drain is backed up.

Symptom, likely cause

Completely dead, status light off: no power to the furnace (breaker, switch, door switch or transformer). Status light on, no response to thermostat: thermostat, wiring or control board. Light blinking: a fault code; the legend is inside the door. Fan runs, nothing else: the safety chain or ignition; see our ignition page. Clicking: ignition issue.

What we test

We test line voltage at the furnace, the 24-volt transformer, the control board, the door switch and the thermostat wires, and we trace the safety chain (limit, rollout and pressure switches) if the board has power but nothing follows.

Related problems

Clicking without flame is an ignition problem; see our ignition page. A furnace that starts and then stops is covered by our shutting-off page.

When to stop

If you smell gas leave and call Peoples Gas at 866-556-6002. If the breaker trips repeatedly or you smell burning, stop and call. Call (773) 514 3683 and tell us what the status light does.

Technician insight

In Chicago 60634, the thing that catches most people out with Furnace Won't Turn On is the combination of 60-year-old wiring and tight basement access around Irving Park Road—homeowners often replace the thermostat first when the real issue is a tripped rollout switch from restricted return air in the original gravity ducts.

Bungalow on the 6900 block of W Irving Park

Homeowner reported the furnace silent after a cold snap. Inspection showed the rollout switch open due to a partially blocked flue shared with the upstairs unit. Cleared the vent, replaced the switch, and verified proper draft before restoring heat.

Furnace Won't Turn On Services We Offer

✓Power and Breaker Diagnosis

Trace power loss to the furnace from the breaker to the switch and disconnect.

✓Transformer and Control Board Testing

Test the low-voltage side that tells the furnace to start.

✓Door, Rollout and Float Switch Repair

Replace safety switches that block startup, and find out why they opened.

Furnace Won't Turn On Cost in Chicago 60634, IL

Service Typical Range What Affects It
Diagnostic visit $99–$150 Includes testing of power, thermostat, and safety switches
Igniter replacement $180–$320 Parts and labor; varies by furnace model
Limit or rollout switch $140–$260 Depends on access and whether venting needs clearing
Transformer replacement $160–$280 Includes wiring inspection in older homes

Ranges are typical for Chicago 60634, IL and confirmed with an exact written quote before any work starts.

How it works

  1. 1

    Confirm power

    Breaker, switch and voltage at the unit.

  2. 2

    Test low-voltage

    Transformer, thermostat and board.

  3. 3

    Written quote

    Price before parts.

  4. 4

    Test startup

    Full cycle.

Pricing

We give a written quote after testing, before any parts are replaced.

Furnace Craft Co — Furnace Repair in Chicago 60634

Good to know

Furnace Won't Turn On — FAQs

Still have questions? We're happy to talk it through.

(773) 514 3683
+ Why won't my furnace turn on at all?
Power, a safety switch, a transformer or the thermostat are the common causes.
+ Should I reset the breaker?
Once is fine. If it trips again, stop and call us.
+ What if it clicks?
That is ignition; see our ignition page.
+ Could the thermostat batteries be dead?
Yes. A blank thermostat is a common reason for a furnace that does nothing.
+ Why does the panel matter?
A door switch prevents the furnace from running with the panel off. A loose panel can keep it from starting.

Furnace stopped working? Call us now

Call Furnace Craft Co and describe the problem. Satisfaction guaranteed on all furnace repair and maintenance work performed.

Call now Get help