Furnace Craft Co logo Furnace Craft Co

Furnace Repair

Furnace Not Heating in Chicago, IL

Furnace on but the house will not warm up: a checklist, the likely causes and when to call us.

  • ✓Owner-operated
  • ✓Shop on W Irving Park Rd
  • ✓Gas and electric furnaces

Quick answer: if the furnace runs but your home stays cold, check three things first: thermostat set to heat, a clean filter and open registers. If those are fine, call (773) 514 3683 and tell us whether the burners light and whether the air from the vents is warm. That answer sorts most causes.

Furnace runs, heat is weak

Weak heat usually means restricted airflow (clogged filter, closed or blocked registers, blocked return), a furnace short on gas input, a failing limit or a thermostat that is off calibration. If the furnace runs constantly but never catches up, the system may be undersized or the ducts leaking, which is common in older houses.

Symptom, likely cause, first check

Warm air but house never reaches setpoint: dirty filter, closed registers, blocked return or leaking ducts. Lukewarm air: weak flame or a gas input problem. Only some rooms cold: duct, damper or register issue in that run. Heat arrives only for a minute: limit tripping on poor airflow. We measure temperature rise across the furnace to tell weak output from duct loss.

What you can safely do

Replace the filter, open every register and make sure the return grille is not blocked by boxes or furniture, which is common in finished basements. Check the thermostat is on heat with a setpoint above the room temperature.

Cold rooms versus no heat

If the whole house is cold and the burners do not fire, see our no-start and ignition pages. This page covers a furnace that runs but does not deliver enough heat.

Chicago housing context

With a median build year of 1952 and many two-flats in ZIP 60634 (ACS 2020-2024), duct runs have often been modified over decades, which can leave rooms with poor airflow. Chicago's January normal low at O'Hare is 18.8 F (NWS 1991-2020), enough that a weak furnace never catches up.

When to call

If those checks do not fix it, call (773) 514 3683. If you smell gas, leave and call Peoples Gas at 866-556-6002.

Technician insight

In Chicago 60634 the thing that catches most people out with Furnace Not Heating is restricted return air from finished basement ceilings. The original ductwork in Irving Park two-flats was never sized for the extra rooms added later, so the furnace overheats and trips the limit before homeowners notice low airflow.

Irving Park Two-Flat No Heat Call

Homeowner reported the furnace running but no warm air. We found the return grille in the finished basement blocked by stored boxes and a tripped limit switch. After clearing the grille and resetting the switch, temperature rise returned to spec and the system stayed online through the next cold front.

Furnace Not Heating Services We Offer

✓Airflow Diagnosis

Check filter, blower, registers, return and accessible ducts for restrictions.

✓Thermostat and Control Testing

Confirm the thermostat is calling and the furnace is responding.

✓Temperature-rise and Burner Check

Measure how much the furnace heats the air and check the flame to see if it is producing full heat.

Furnace Not Heating Cost in Chicago 60634, IL

Service Typical Range What Affects It
Thermostat replacement $180–$320 Depends on smart vs standard model and wiring access in older homes
Hot surface igniter $220–$380 Includes part and labor; higher on 90%+ furnaces with limited cabinet access
Blower motor service $350–$650 ECM motors cost more; PSC units are lower
Pressure switch replacement $190–$290 Includes vent inspection

Ranges are typical for Chicago 60634, IL and confirmed with an exact written quote before any work starts.

How it works

  1. 1

    Check the basics

    Thermostat, filter, registers and breaker.

  2. 2

    Measure temperature rise

    We measure how much the furnace heats the air to find under-performance.

  3. 3

    Written quote

    You see the fix and cost before work.

  4. 4

    Verify

    We re-measure after the repair.

Pricing

We give a written quote after on-site diagnosis, before any work starts.

Furnace Craft Co — Furnace Repair in Chicago 60634

Good to know

Furnace Not Heating — FAQs

Still have questions? We're happy to talk it through.

(773) 514 3683
+ Why is my furnace running but not heating?
Common causes are clogged filters, blocked airflow, a weak flame or a thermostat fault.
+ Is this the same as cold air from vents?
Not exactly. Cold air from vents when the furnace should be on has its own page; this page is for weak heat.
+ Why are only some rooms cold?
Closed registers or a duct problem in that run are the usual causes.
+ How do I know if I need a new furnace?
Age, repeated repairs and the cost of the fix guide the decision; we explain both options.
+ Can a dirty filter really cause this?
Yes. A clogged filter restricts airflow, lowers heat output and can trip the limit switch.

Furnace stopped working? Call us now

Call Furnace Craft Co and describe the problem. Satisfaction guaranteed on all furnace repair and maintenance work performed.

Call now Get help